Fluke 417D Laser Distance Meter
| 417D |
|---|
| Typical range [1] | 0.2-40 m/0.6-131 ft |
| Typical measuring tolerance* [1] | 2.0 mm ± 1.5 mm/± 0.06 in *** |
| Maximum measuring tolerance [2] | ± 3.0 mm/0.12 in *** |
| Accuracy up to 10m (+/-) | ± 2 mm |
| Display | 2 line/1 mm/1/32 in |
| Display illumination | Yes |
| Laser point at distance | 6/30/60 mm (10/40/100 m) |
| Area | Yes |
| Units setting (smallest units displayed) | 0,000m, 0' 00'' 1/32, 0 in 1/32 |
| Auto laser switch off | 90 sec |
| Auto power switch off | 180 sec |
| General |
| Laser class | II |
| Laser type | 635 nm, <1 mW |
| Protection class | IP54 |
| Battery life (2 x AAA) 1.5 V NEDA 24A/IEC LR03 | Up to 3,000 measurements |
| Size (Hx W x D) | 11.9 x 3.8 x 2.6 cm |
| Drop test | 1 meter |
| Weight (with batteries) | 95g (3.35 oz) |
| Temperature range: Storage | -25 °C to 70 °C (-13 °F to 158 °F) |
| Temperature range: Operation | -10 °C to 50 °C (14 °F to 122 °F) |
| Calibration cycle | Not applicable |
| Maximum relative humidity | 85 % @ 20°F to 120 °F
(-7 °C to 50 °C) |
| Safety | CAN/CSA-C22.2 No. 61010-1-04, UL Std. No. 61010-1 (2nd Edition),
ISA-82.02.01, IEC Standard No. 61010-1:2001, EN60825-1:2007 (Class
II) |
| EMC | 61326-1:2006 |
[1] Applies for 100 % target reflectivity (white painted wall), low
background illumination, 25 °C (13 °F).
[2] Applies for 10 % to 500 % target reflectivity, high background
illumination, -10 °C to +50 °C (14 °F to +122 °F).
[3] Tolerances apply from 0.05 m to 10 m (0.001 ft to 32.8 ft) with
a confidence level of 95 %. The maximum tolerance may deteriorate
to 0.1 mm/m (0.003 in/ft) between 10 m to 30 m (32.8 ft to 98.4 ft)
and to 0.15 mm/m (0.005 in/ft) for distances above 30 m (98.4 ft).
[4] Applies for 100 % target reflectivity, background illumination
between 10,000 lux and 30,000 lux.
[5] After user calibration. Additional angle related deviation of ±
0.01° per degree up to ± 45° in each quadrant. Applies at room
temperature. For the whole operating temperature range the maximum
deviation increases by ± 0.1°.
Fluke 62 MAX+ IR Thermometer
| 62 MAX+ |
|---|
| Temperature range | - 30 °C to 650 °C
(-22 °F to 1202 °F) |
| Accuracy (Calibration geometry with ambient temperature 23 °C +/- 2
°C) | ± 1.0 °C or ± 1.0 % of reading, whichever is greater
± 2.0 °C at -10 °C to 0 °C
± 3.0 °C at -30 °C to -10 °C |
| Optical resolution | 12:1
(calculated at 90 % energy) |
| Response time (95 %) | < 300 ms (95 % of reading) |
| Spectral response | 8 to 14 microns |
| Emissivity | 0.10 to 1.00 |
| Display resolution | 0.1 °C (0.2 °F) |
| Repeatability (% of reading) | ± 0.5 % of reading or ± 0.5 °C (whichever is greater) |
| Power | 1 AA alkaline battery |
| Battery life | 8 hours with laser and backlight on |
| Weight | 255 g (8.99 oz) |
| Size | (175 x 85 x 75) mm
(6.88 x 3.34 x 2.95) inches |
| Operating temperature | 0 °C to 50 °C
(32 °F to 122°F) |
| Storage temperature | -20 °C to 60 °C
(-4 °F to 140 °F)
(without battery) |
| Operating humidity | Non- condensing @ ≤ 10 °C (50 °F)
≤ 90 % RH @ 10 °C (50 °F) to 30 °C (86 °F)
≤ 75 % RH @ 30 °C (86 °F) to 40 °C (104 °F)
≤ 45 % RH @ 40 °C (104 °F) to 50 °C (122 °F) |
| Operating altitude | 2000 meters above mean sea level |
| Storage altitude | 12,000 meters above mean sea level |
| Drop test | 3 meters |
| Implement standard | Q/ASF01 |
| Standards and agency approval |
| Compliance | IEC 61010-1: Pollution Degree 2 |
| Laser safety | IEC 60825-1 Class 2, 650 nm, < 1 mW |
| Ingress protection rating | IP 54 per IEC 60529 |
| Warranty | 3 years |
